Skip to content
From Knee Height

Babyproofing guides for the home you have.

Magnetic locks for thick doors and drawer fronts

Measure from the outside key position to the inside face where the lock will sit. On a drawer that can mean two layers of wood. If the panel stays intact, you need to know whether the key activates the latch across those layers. If the lock requires a drilled bore, the thickness selects the installed parts and drilling setup.

What the thickness spansIllustration, not to scale.
Across an intact door — schematic viewAcross an intact door

The bracket spans uninterrupted material between the external key and the inside mounting face.

Through a built-up front — schematic viewThrough a built-up front

The bracket spans the decorative face and the drawer-box front together. The recessed part enters from inside. The catch sits on a separate block.

From Knee Height editors · Sources checked November 17, 2026

Measure at the spot where the key will go

Open the door and find a flat place for the inside lock and a stationary place for its strike, the piece that catches the latch. Look directly across from the lock for the outside key position. On a paneled door, the thin center and the thicker edge may give very different readings. Record the material as well as the thickness.

For a drawer with an applied front, follow a line from the visible outer face to the proposed inside mount. Rev-A-Shelf’s drawer drawing labels this measurement T. It includes both the decorative face and the drawer-box front. If the lock sits behind both, measuring just the exposed edge of the decorative front leaves out part of the distance.

Sources · Rev-A-Lock drawer installation drawing, T and section A–A

Will the key work through an intact front?

Safety 1st supplies a practical check for HS292. Before peeling a liner, hold the original lock inside and its matching key directly opposite on the outside, at the proposed position. Follow the guide’s setup and watch the button on top of the lock. It should retract. If it does not, leave the parts unattached. The ⅜-inch mark elsewhere in the guide is for pilot-hole depth. The guide gives no maximum operating thickness.

KidCo S3365, sold as four locks and a key, also opens from the outside. Its package guide gives no numerical magnetic reach. If you need a thickness figure before buying, ask KidCo about the measured thickness and material of your front.

Sources · Safety 1st HS292, page 2 activation check and pilot-hole marking · KidCo S3365 package instructions

What Qdos means by 1½ inches

The original Qdos FAQ says the 17-10006 magnetic key can operate through 1½ inches of wood, including the built-up front of a drawer. This is the manufacturer’s claim for that model and material. Its March 2017 manual also requires a standard face frame and excludes frameless and flush-framed cabinets. A front can meet the wood measurement and still have the wrong mounting geometry.

This is a legacy example. The white four-lock, one-key US pack was out of stock at the November 17, 2026 offer check. If you already have the kit, identify its parts in the linked guide before relying on the FAQ’s figure.

Sources · Original Qdos FAQ, key operation through wood · Qdos Adhesive Magnet Lock manual, March 2017, pages 2–3

How the Rev-A-Lock thickness chart works

Rev-A-Shelf’s RAL-101-1 starter set uses a drilled recess and a screwed-in assembly. Read the front thickness against the chart in I-RLTL-0615 and the drawer detail if applicable. The chart covers ½–⅝ inch, ⅝–1⅛ inches and 1⅛–1 9/16 inches. At a shared endpoint, use the maker’s drawing or ask Rev-A-Shelf to confirm the parts before drilling.

QuestionWhat to measure or observeWhat the result tells you
Will an intact-panel key operate?With HS292, watch the button during the model’s check at the actual panel.Activation there is one check. Catch placement and secure attachment still need checking.
Which Rev-A-Lock parts fit?Measure actual front thickness, including both drawer-front layers.The drawer detail shows the assembly alone in the thinnest band, a plunger in the middle band and an extension for the thickest band.
Can the strike catch the latch?Locate the fixed mounting face relative to the moving lock. On the Rev-A-Lock drawer drawing, locate the separate strike block and account for bumpers.You need support for the strike, even with a front inside the chart. The installer supplies the block.
How deep can the bore go?Use the measured front and the depth-gauge instructions for the exact drilled assembly.This controls how much material remains at the outer face. It provides no operating range for a key across an intact front.

Sources · Rev-A-Lock I-RLTL-0615, thickness chart and depth gauge · Rev-A-Lock drawer configuration, strike block and bumpers · Safety 1st HS292, separate activation and drilling checks

A 1¼-inch wood drawer front, worked on paper

Suppose the decorative face measures ¾ inch and the drawer-box front adds ½ inch at the proposed mount. Together they measure 1¼ inches. That puts this Rev-A-Lock drawer in the chart’s thickest band. Before buying, find where the strike block in the drawing would attach, check where the bumpers stop the closed drawer and confirm that you may drill the front.

If the combined front exceeds 1 9/16 inches, this chart has no matching row. If the material is glass or metal, the product page’s materials list gives no material-specific drilling procedure. Ask the maker about your front. If drilling is off the table, return to a mechanism that uses the cabinet geometry you actually have.

Sources · Rev-A-Lock door thickness chart · Rev-A-Lock drawer section and strike support · Rev-A-Shelf RL Series product description

Check the exact model

As an Amazon Associate I earn from qualifying purchases.

Rev-A-Shelf Rev-A-Lock cabinet security starter set · RAL-101-1

5 locks and 2 keys. Requires a depth-controlled bore. Compare the thickness of your whole drawer front with the component chart in the installation guide. Read the manufacturer’s instructions.

Buy on Amazon