Skip to content
From Knee Height

Babyproofing guides for the home you have.

How to remove adhesive babyproofing locks

First put restricted contents somewhere else and keep children away from loose parts. Identify the lock, the piece you want to remove and any screws. A release tab may free a working arm while leaving its adhesive plate on the cabinet. Permanent removal needs instructions for the part still attached.

Name the attached pieceIllustration, not to scale.
Arm, plate and pad — schematic viewArm, plate and pad

The hook-ended arm is above its mounting plate. The adhesive pad sits beneath the plate.

Catch or storage post — schematic viewCatch or storage post

A projecting lip catches a latch. A post stores an accessory. Look up the instructions for the piece still attached.

From Knee Height editors · Sources checked November 17, 2026

Name the piece that is stuck

On an open cabinet, look for the working latch on the moving front and the catch it meets on the fixed frame. A mounting plate may sit underneath the latch. A small post elsewhere might only hold a cap or key. Photograph each piece and its markings, including screw heads.

For a lock left by a previous occupant, ask for the model number or package before using a tool on the finish. If you can identify only the brand, send the photographs to its support team. The same maker can specify different methods for different pieces.

Sources · Qdos double-door guide, parts list and storage post · Qdos SureCatch parts list and page 11 removal instructions

Safety 1st magnetic lock, press latch and strap

For the HS292 magnetic lock, the removal section describes working dental floss or fishing line back and forth through the adhesive behind the lock, then rolling the residue off the door. The guide lists a hair dryer as an optional aid to soften the adhesive. Check the cabinet maker’s finish guidance before applying heat. Identify any installed screws first, since the adhesive instructions address only the tape bond.

HS395 has its own guide, 4358-8584. Its removal section also describes floss or fishing line, rolling away residue and optional heat. Check the printed model and the parts actually screwed in before following it.

For HS270, release the strap housing as for normal opening. Both rev. B and rev. F describe easing dental floss between the adhesive and the contact surface. For residue they allow a soft cloth and warm soapy water or rolling it off with your fingers, subject to the furniture or appliance maker’s cleaning advice. Both revisions say permanent removal ends use of the strap.

Sources · Safety 1st HS292 guide, To Remove on page 2 · Safety 1st HS395–HS397, guide 4358-8584 · Safety 1st HS270 rev. B, permanent removal · Safety 1st HS270 rev. F, permanent removal

Qdos removal depends on the component

The SureCatch top and lower guides distinguish disabling the latch from removing adhered hardware. Before working behind a plate, check whether its drawer installation used the required setup 2B screw. If any hardware or finish detail is unclear, ask the maker how to release that part.

Exact partWhat the guide describesFinish or reuse limit
17-10013 or 17-10014 SureCatch locking armFor temporary removal, press both locking tabs together and slide out the arm.This disables the latch and leaves the plate attached.
17-10013 or 17-10014 mounting plate and fixed catchFor permanent removal, the guide shows careful leverage with a rounded knife at a plate corner and behind the catch to split the tape. Rub residue away with a finger.The maker acknowledges possible finish damage. Use a cleaner only if compatible with that surface. The pad is for one placement.
17-10001 double-door lock, cap storage postPage 3 describes working a rounded knife behind the edge of this post until the tape tears, then rubbing away residue.This instruction covers the small storage post. Use only a finish-compatible cleaner if residue remains.
17-10001 double-door lock, catch on the cabinet frameThe guide supplies no permanent-removal method for the main frame catch. Ask Qdos about this specific part.Leave the catch in place while you obtain instructions for the component and finish.

Sources · Qdos 17-10013 SureCatch, page 11 · Qdos 17-10014 SureCatch, page 11 · Qdos 17-10001, storage post on page 3

If the coating starts to lift

Stop as soon as paint, veneer or another surface layer starts coming away. Keep the area inaccessible and photograph it with the hardware in place. Give the cabinet maker the finish name if you know it, and give the lock maker the model, component and what you observed. Permission to use a tool on a particular latch does not tell you how an older or refinished coating will respond.

Sources · Qdos SureCatch, removal and possible surface damage · Safety 1st HS395 guide, weakly bonded and refinished surfaces

Decide what to keep

Account for loose catches, caps, screws and any magnetic key before returning the cabinet to use. Retire a permanently removed HS270. For a one-placement Qdos pad, ask the maker whether it supplies an approved replacement for that exact model before planning another installation. If the maker gives no reinstallation method, keep the removed device out of service.

Sources · Safety 1st HS270 permanent-removal limit · Qdos SureCatch single-placement adhesive instructions · Safety 1st HS292 key and small-part precautions