Skip to content
From Knee Height

Babyproofing guides for the home you have.

Why adhesive cabinet locks keep coming off

If a pad is lifting or a latch has come off, treat the cabinet as accessible now. Move medicines and cleaning products to locked storage beyond reach, and collect the loose pieces. Before trying another installation, identify the part that moved and the surface it left behind.

Which layer moved?Illustration, not to scale.
The pad lifted — schematic viewThe pad lifted

A gap opens under the adhesive pad. The thin finish layer stays flat against the cabinet.

The finish lifted too — schematic viewThe finish lifted too

The coating rises with the pad and leaves the underlying cabinet material exposed.

From Knee Height editors · Sources checked November 17, 2026

Look at both sides of the separation

Keep the pieces away from children. Take a photo of the cabinet and the back of the loose part before cleaning either. Note the model, where each part sat, how long it had been attached and whether it ever caught properly. These observations give the manufacturer something specific to assess.

What you seeWhat to checkWhen to stop
Pad peeling from an otherwise intact surfaceCompare the location, surface preparation and waiting time with the exact guide.The maker gives no way to reinstall the used pad. Ask about the exact component.
Paint or a layer of board stuck to the padCheck where the cabinet surface itself separated. Photograph the exposed area.Keep pressure off the damaged finish and consult the cabinet maker before attaching anything there.
Plate rocks against a raised screw headLook side-on for a point that prevented full contact. Compare the plate position with the model drawing.The supported area in the drawing is missing or a single-placement pad has already been applied.
Both parts still attached, but the door opensWatch where the moving hook passes the fixed catch, and check the model’s active or bypass position if it has one.The mechanism is damaged, the alignment cannot be confirmed or the front opens despite the required check.

Sources · CPSC poison prevention and locked storage · Safety 1st HS395 warnings about parts, attachment and malfunction

Match the surface check to the name on the lock

Safety 1st HS395 specifies isopropyl alcohol on the contact areas, complete drying, and at least 24 hours with the lock disengaged before checking the bond. Its manual and the HS292 magnetic manual warn about oily surfaces, refinished cabinetry and material that can come away in layers, including old paint. A pad carrying a chip of the cabinet coating calls for checking the finish as well as the lock.

The KidCo S3313 three-pack calls for flat, smooth, dry mounting surfaces free of grease. Decide the position while the liners are still on. The S3313 sheet describes a 24-hour setting period and included screws if the installation is insecure. Use the model on the package when contacting KidCo. Its current S3314 four-pack has a different model number.

Sources · Safety 1st HS395–HS397, preparation and attachment check · Safety 1st HS292, surface limitations · KidCo S3313 package, preparation and tape setting time · KidCo S3314 four-pack identity

On Qdos SureCatch, the screw depends on where the plate sits

For the 17-10013 top-drawer and 17-10014 lower latches, look for a projecting screw head under the mounting plate. The guides call for a dry run, full contact where shown and at least 30 seconds of pressure at the indicated bonding steps. The tape allows one placement.

In drawer setup 2B the mounting plate is only partly supported, so the instructions require the supplied screw. The door setup in the 17-10014 guide expressly forbids that screw because it could come through the front. The advertised adhesive mount tells you very little about which of those two instructions applies.

Sources · Qdos 17-10013, placement and drawer setup 2B · Qdos 17-10014, drawer setup 2B and door installation · Cardinal Gates description of the adhesive lower latch

What to check after the waiting period

For an installation made according to the HS395 or HS292 guide, allow the adhesive at least 24 hours before the specified firm tug on the front. If it fails to hold, follow the guide’s directions for the supplied screws and confirm the mounting surface is suitable. HS395 directs replacement of a broken or malfunctioning device.

Qdos SureCatch also specifies 24 hours before use. The separate 17-10006 magnetic guide suggests letting the adhesive set overnight. A shorter wait is worth recording when you contact support. Time alone cannot tell you whether the plate was aligned, the surface failed or the latch was damaged.

Sources · Safety 1st HS395, after-installation check · Safety 1st HS292, adhesive and hardware check · Qdos SureCatch top-drawer guide, wait before use · Qdos magnetic lock, March 2017 setting advice

If the model or the next step is still unclear

For an inherited lock, collect any lettering on the housing, a photo of both halves and the package or purchase record if available. Ask the manufacturer whether the part can be used again on the named finish and whether an exact replacement is available. If the finish came away, also send that photo to the cabinet maker. Leave the cabinet out of use for restricted items until you have a working arrangement.

Sources · Safety 1st Home Safety Help Center · KidCo home safety questions and support