Skip to content
From Knee Height

Babyproofing guides for the home you have.

Babyproofing frameless and inset cabinets

Open the door to see how the cabinet box is built. Close it to see where the front sits. Then find the fixed surface the lock’s catch needs. A cabinet described as “flush” can look right from the hallway and still lack the mounting face shown in the instructions.

The box and the frontIllustration, not to scale.
Framed box — schematic viewFramed box

The hatched rails and stiles form a separate frame around the opening.

Frameless box — schematic viewFrameless box

The thin edges you see around the opening belong to the box itself.

Inset front — schematic viewInset front

Viewed from above, the solid door sits inside the opening, flush with the frame.

Overlay front — schematic viewOverlay front

Viewed from above, the solid door closes across part of the hatched frame.

From Knee Height editors · Sources checked November 17, 2026

Look at the box and the door separately

A face frame is the border attached to the front of the cabinet box. Its rails run across the opening and its stiles run vertically. On a frameless cabinet, opening the door exposes the edges of the box itself. A door can hide most of a face frame, so two rows of closed, flat-front cabinets can look much alike.

Inset describes a front that closes within the opening. Overlay describes a front that covers some or all of the edge around it. Sketch a side view of the door closed, then an open view showing the face you would attach the catch to. Keep “handleless” as a separate note about how you open the door.

Sources · Omega Cabinetry, Cabinetry 101 definitions and illustrations

Follow the bend in the Safety 1st catch

The white four-pack HS395 has a hinged catch. On a face frame, its two surfaces form a right angle around the frame. On a frameless box, the catch lies flat. With the parts held in the illustrated position, check where the moving arm will meet the catch and whether the front can close. The frame label alone leaves the setback of an inset door unanswered.

For the framed installation, Safety 1st guide 4358-8584 specifies a face frame at least 1.35 inches (3.4 cm) high. Measure the fixed frame where the catch will sit. The manual shows a separate flat-catch arrangement for a frameless box.

Look for instruction number 4358-8584, dated July 2024, with HS395–HS397 printed on it. The HS395 product page links to this guide. At our November 17, 2026 source check, the help-center download for the family opened a sheet marked HS310/315/316. Use the sheet that names your model.

Sources · Safety 1st HS395–HS397, guide 4358-8584 · Safety 1st HS395 four-pack and instruction download · Safety 1st Home Safety Help Center

Where can the catch actually land?

Open a drawer and the door below it. If the strip you thought was a divider moves out with the drawer, it cannot hold a stationary catch for the door. A side-mounted hook approaches its catch near the cabinet wall instead. Use a side mount only when the model instructions show one.

Cabinet observationModelDocumented arrangementStill to check
Door below a drawer with no dividerKidCo S333-12, 12 locksThe maker permits a screw-mounted side position.Find a fixed side landing and room for the hook to engage as the door opens.
Frameless boxKidCo S337, four locksKidCo lists extra frameless hardware with this screw-mounted spring latch.Identify those parts in your kit and confirm placement. The package sheet gives no separate frameless sequence.
Face frame or frameless boxKidCo S3313, three locksFigure A uses an angled catch on a frame. Figure B uses an adjustable sliding catch on a frameless box.Compare the catch in hand with the right figure and check the flat contact area.

Sources · KidCo S333-12 side-mount instructions · KidCo FAQ on cabinets without a divider · KidCo S337 dimensions and included frameless hardware · KidCo S337 package and mounting figures · KidCo S3313 package, framed figure A and frameless figure B

When a flush front rules out a model

Page 3 of both Qdos SureCatch guides shows three pairs of front and side views. The top-drawer 17-10013 and lower-drawer/door 17-10014 guides cover the standard framed drawing and exclude the frameless and flush-framed drawings. If your inset front closes into the frame as in the excluded view, set those two models aside. If the edge profile is different, send the maker both views before selecting a mounting point.

Sources · Qdos SureCatch top-drawer guide, cabinet types on page 3 · Qdos SureCatch lower-drawer and door guide, page 3

Finish the sketch before choosing parts

Mark the fixed face, the moving face and their meeting point on one sketch. If all three agree with the named model’s diagram, continue to its surface and clearance checks. If the diagram excludes your layout, move on. If you cannot mark a meeting point, send the sketch, dimensions and model number to the manufacturer.

Use the number printed on the parts or package. KidCo’s S335 sheet identifies a magnetic key set. Its FAQ reference to a side-mount accessory does not establish a side mount for the S3365 lock.

Sources · KidCo S335 key-set instructions · KidCo home safety questions · KidCo S3365 lock-set instructions

Check the exact model

As an Amazon Associate I earn from qualifying purchases.

Safety 1st Secure-to-Explore Adhesive Locks · HS395

4 locks, white. The hinged catch changes position for framed and frameless cabinets. Check space for the latch and for adult release before attaching it. For a framed installation, its guide specifies a minimum frame height of 1.35 inches (3.4 cm). Read the manufacturer’s instructions.

Buy on Amazon